USER QUICK-GUIDE

 

In first place we would like to acknowledge our appreciation for the confidence you have shown in our web-site www.templyzer.com and in our products.

If you have purchased a Thermograph LogTag and USB connection, before using them, one must follow our instructions for a correct use.

 

1.- INSTALLATION OF LOGTAG ANALYZER SOFTWARE.


The software for Windows can be downloaded for free once the order has been placed and received.

 

Go to www.templyzer.com/en/software/36-software-logtag-analyzer-23.html , if you are registered on our site, a download button will appear.

 

The installation is simple, follow the steps indicated during installation. Upon finishing, you will also have installed the necessary drivers and controls for the USB LogTag Base.

 

2.- CONNECTING THE USB BASE


‎Once the software is installed, connect the USB LogTag Base to the computer. Wait a few moments while it is detected and installed by the computer. For Windows XP it is necessary to reboot the computer so that it can be detected correctly.

 

2.1 If the computer does not detect the base, most times it is because the USB base has been connected before installing the software. If this is the case, go to Control panel / Hardware/device manager  and eliminate the controller with the exclamation mark called “Unknown device”, then disconnect the Base from the computer and reconnect so as to configure correctly. 

 

3.- STARTING UP THE LOGTAG ANALYZER AND INTRODUCING A THERMOGRAPH INTO THE USB BASE.


The software will detect that it is the first time a thermograph has been connected and will open the configuration screen.

 

3.1 Inthe case the installation screen does not open, choose the option LogTag/Configure situated in the top menu. if the screen still does not appear consult point2.1 in our guide.

 

4.- CONFIGURATION OF THE THERMOGRAPH LOGTAG.


In this window you will find all the parameters  and limits that can be defined, such as:

 

4.1.-  An identity that can be assigned to each thermograph to distinguish them. 

4.2.-  The Start button or select a date and time for automatic start up.

4.3.-  The days needed to be read before collecting the readings. 

4.4.-  The pause time needed while starting and placing in the desired location.

4.5.-   The definition of the alarms on the graph when the minimum or maximum temperature limits have been breached. 

4.6.-Readingcontrols and configuration using a password. 

 

Once defined, click next button and the details will be sent to the thermograph, at this moment the device is ready to be started.

 

5.- HOW TO SEE THE TEMPERATURE READINGS COLLECTED BY THE THERMOGRAPH.


Once the LogTag Analyzer software has been started, introduce the thermograph into the previously connected USB Base.

 

It will automatically recognise that the thermograph has saved readings, immediately they will be shown and saved on the hard drive. Consult the sub section on how to send collected readings by email or to a FTP server.

 

At this moment the thermograph will be ready for a new configuration and to start a new recording. Consult the sub section on automatic configuration.

 

INTERESTING OPTIONS

 

6.- AUTOMATIC CONFIGURATION OF THE THERMOGRAPH AFTER EACH COLLECTION OF READINGS.


Each time the thermograph is connected to the computer to collect the readings, we can predetermine that it reconfigures to the last set of parameters introduced.  To do so, access the superior menu on the LogTag Analyzer Software. Choose Edition/options/ Automate, and choose the option “Re-configure with same settings after automatic download”.

 

7.- GENERATE A REPORT BETWEEN A RANGE OF DATES.


It is possible that you may need a report on the temperatures a merchandise has been exposed to over a range of dates. To do so, you must open the graph in question, leftclick on the area required, then choose option “Report” situated under the graph where the generated document can be seen, ready to be saved and/or sent by email. 

 

8.- SENDING OF READINGS AUTOMATICALLY BY EMAIL OR TO A FTP SERVER.

(Highly recommended option for work between offices.)

 

As in the sub-section of the previous point, access Edition/options/ Automate activate and configure the desired setting.

 

If you would like any of these options to be configured by the team at Templyzer let us know through the Contact Form

Cart  

No products

Shipping 0,00 €
Total 0,00 €

Check out

Pago Seguro
Transporte gratis por compras superiores a 300
Transporte gratis por compras superiores a 300